/////////////////////////////////////////////////////////////////////
////                                                             ////
////  UTMI Interface                                             ////
////                                                             ////
////                                                             ////
////  Author: Rudolf Usselmann                                   ////
////          rudi@asics.ws                                      ////
////                                                             ////
////                                                             ////
////  Downloaded from: http://www.opencores.org/cores/usb/       ////
////                                                             ////
/////////////////////////////////////////////////////////////////////
////                                                             ////
//// Copyright (C) 2000 Rudolf Usselmann                         ////
////                    rudi@asics.ws                            ////
////                                                             ////
//// This source file may be used and distributed without        ////
//// restriction provided that this copyright statement is not   ////
//// removed from the file and that any derivative work contains ////
//// the original copyright notice and the associated disclaimer.////
////                                                             ////
////     THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY     ////
//// EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED   ////
//// TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS   ////
//// FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL THE AUTHOR      ////
//// OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,         ////
//// INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES    ////
//// (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE   ////
//// GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR        ////
//// BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF  ////
//// LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT  ////
//// (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT  ////
//// OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE         ////
//// POSSIBILITY OF SUCH DAMAGE.                                 ////
////                                                             ////
/////////////////////////////////////////////////////////////////////

//  CVS Log
//
//  $Id: utmi_if.v,v 1.0 2001/03/07 09:17:12 rudi Exp $
//
//  $Date: 2001/03/07 09:17:12 $
//  $Revision: 1.0 $
//  $Author: rudi $
//  $Locker:  $
//  $State: Exp $
//
// Change History:
//               $Log: utmi_if.v,v $
//               Revision 1.0  2001/03/07 09:17:12  rudi
//
//
//               Changed all revisions to revision 1.0. This is because OpenCores CVS
//               interface could not handle the original '0.1' revision ....
//
//               Revision 0.2  2001/03/07 09:08:13  rudi
//
//               Added USB controll signaling (Line Status) block. Fixed some minor
//               typos, added resume bit and signal.
//
//               Revision 0.1.0.1  2001/02/28 08:11:45  rudi
//               Initial Release
//
//

`include "usb_defines.v"

module utmi_if( // UTMI Interface (EXTERNAL)
        phy_clk, rst,
        DataOut, TxValid, TxReady,
        RxValid, RxActive, RxError, DataIn,
        XcvSelect, TermSel, SuspendM, LineState,
        OpMode, usb_vbus,

        // Internal Interface
        rx_data, rx_valid, rx_active, rx_err,
        tx_data, tx_valid, tx_valid_last, tx_ready,
        tx_first,

        // Misc Interfaces
        mode_hs, usb_reset, usb_suspend, usb_attached,
        resume_req
        );

input       phy_clk;
output      rst;
output  [7:0]   DataOut;
output      TxValid;
input       TxReady;
input   [7:0]   DataIn;
input       RxValid;
input       RxActive;
input       RxError;
output      XcvSelect;
output      TermSel;
output      SuspendM;
input   [1:0]   LineState;
output  [1:0]   OpMode;
input       usb_vbus;

output  [7:0]   rx_data;
output      rx_valid, rx_active, rx_err;
input   [7:0]   tx_data;
input       tx_valid;
input       tx_valid_last;
output      tx_ready;
input       tx_first;

output      mode_hs;    // High Speed Mode
output      usb_reset;  // USB Reset
output      usb_suspend;    // USB Suspend
output      usb_attached;   // Attached to USB
input       resume_req;

///////////////////////////////////////////////////////////////////
//
// Local Wires and Registers
//
reg [7:0]   rx_data;
reg     rx_valid, rx_active, rx_err;
reg [7:0]   DataOut;
reg     tx_ready;
reg     TxValid;
wire        drive_k;

///////////////////////////////////////////////////////////////////
//
// Misc Logic
//


///////////////////////////////////////////////////////////////////
//
// RX Interface Input registers
//

always @(posedge phy_clk)
    if(!rst)    rx_valid <= #1 0;
    else        rx_valid <= #1 RxValid;

always @(posedge phy_clk)
    if(!rst)    rx_active <= #1 0;
    else        rx_active <= #1 RxActive;

always @(posedge phy_clk)
    if(!rst)    rx_err <= #1 0;
    else        rx_err <= #1 RxError;

always @(posedge phy_clk)
        rx_data <= #1 DataIn;

///////////////////////////////////////////////////////////////////
//
// TX Interface Output/Input registers
//
wire    tx_valid_sr;

assign  tx_valid_sr = (!rst) ? 0 : tx_valid_last ? 1 : TxReady ? 0 : tx_valid_sr;

always @(posedge phy_clk)
    if(TxReady | tx_first)  DataOut <= #1 tx_data;
    else
    if(drive_k)     DataOut <= #1 8'hff;

always @(posedge phy_clk)
    tx_ready <= #1 TxReady;

always @(posedge phy_clk)
    TxValid <= #1 tx_valid | tx_valid_sr | drive_k;

///////////////////////////////////////////////////////////////////
//
// Line Status Signaling & Speed Negotiation Block
//

utmi_ls u0(
        .clk(       phy_clk     ),
        .rst(       rst     ),
        .resume_req(    resume_req  ),
        .rx_active( rx_active   ),
        .tx_ready(  tx_ready    ),
        .drive_k(   drive_k     ),
        .XcvSelect( XcvSelect   ),
        .TermSel(   TermSel     ),
        .SuspendM(  SuspendM    ),
        .LineState( LineState   ),
        .OpMode(    OpMode      ),
        .usb_vbus(  usb_vbus    ),
        .mode_hs(   mode_hs     ),
        .usb_reset( usb_reset   ),
        .usb_suspend(   usb_suspend ),
        .usb_attached(  usb_attached    )
        );

endmodule